#DELL PRECISION 490 ERROR CODE 1 2 3 CODE#
#DELL PRECISION 490 ERROR CODE 1 2 3 WINDOWS#

#DELL PRECISION 490 ERROR CODE 1 2 3 CODE#

This code is used to log regular messages, mostly to align all the lines in the Yarn output.

YN0071 - NM_CANT_INSTALL_EXTERNAL_SOFT_LINK.

YN0026 - CONSTRAINTS_INVALID_DEPENDENCY.

YN0025 - CONSTRAINTS_EXTRANEOUS_DEPENDENCY.

YN0024 - CONSTRAINTS_INCOMPATIBLE_DEPENDENCY.

YN0023 - CONSTRAINTS_MISSING_DEPENDENCY.

If you are successful in solving the problem I would appreciate you posting the solution since I am very interested in learning more about what causes these problems in BTX form factor motherboards even though they are no longer being produced. The machine needs to be on a workbench where components can be tested and exchanged as necessary. I don't believe the problem you are encountering can be solved in a forum. Motherboard wiring is so complex I don't know of a way by which the Power Good circuitry on a motherboard can be tested without changing the component. If the power supply tests good with two different testers then you have to look further than the power supply as the source of your problem.Р”В®rratic operation that you cannot consistently duplicate is the hardest part of computer troubleshooting, and the problematic part can only be determined by changing parts. There may be very minor variations in voltage and Power Good Signals between two power supply testers, however they should be minor. When I had machines come in for testing I always tested the power supply with two different power supply testers to validate that the voltages and Power Good Signals. A good power supply Power Good Signal will generally be around 330-350ms. The normal response time is less than 500ms. What I would do is take your tower to a shop that has a power supply tester that tests not only the voltage on the rails, but also tests the Power Good Signal response time. I'm not going to write an essay on the Power Good Signal, however you can read about the Power Good Signal here #1-The power supply is not sending a consistent Power Good Signal, or #2-The motherboard circuitry is not responding correctly to a proper Power Good Signal from the power supply. I believe that either one of two things is happening. spasmodic (intermittent) correct operation of either component. This assumption is not correct since you are not considering erratic, i.e.

Maybe I will actually try to remove the fans and blow off the dust and reinstall them? Hope it wont be too difficult?Р”В«y using the rationale that a component (motherboard) worked X number of days without failure was good, then you would have to assume that another component (the power supply) since it also worked for X number of days was also good. I did buy a can of compressed air and tried to dust out computer, ( not sure if I was successful) but I still had the same problem. One user said they just dusted out their computer and it worked after that. Some said they changed their PSU, others changed their video card and others did change their motherboard. I am wondering, since it worked for over 17 days without incident, could it really be the motherboard? If the motherboard was dead it shouldn't have worked, right? I also saw on the dell support board that several other xps 410 users had encountered the same problem, but there doesn't seem to be a universal solution. Of course, this morning when we turned it on, the problem is there again. There was a thunderstorm in our area and lots of lightning, so we decided to shut down everything. We decided not to turn it off again, and see what happened. After I posted on this site, late that evening we tried turning on the machine again and it booted up without incident. Well since I last signed in this is what happened. If you had to have someone replace the board (can't do it yourself), in my opinion it wouldn't be a worthwhile investment considering the cost of new machines today, and the fact that in most cases the warranty on a used board if generally around 30 days or so.

#DELL PRECISION 490 ERROR CODE 1 2 3 WINDOWS#

If you can find a new or used Dell board you should have no problem reinstalling Windows although all of your components should work with a Dell replacement board simply by transferrring the components. You might get lucky and find a new motherboard, however most you will find will be used boards since Intel discontinued further developement of the BTX form factor in 2006 so consequently very few new BTX boards were built after Intel discontinued developement. Personally, if the problem is discovered to be the motherboard I would be hesitant about replacing the board unless you can do it yourself. The only way to find a board for your machine would be to do a Goggle search for Dell XPS 410 motherboards, or you should have a Dell part number stenciled somewhere on the board which you could use in a Google search. If the fan module is running wide open or very fast with no display, this is a classic symptom of motherboard failure. The chance that the problem is the processor is almost nil.

Dell precision 490 error code 1 2 3